|
|
Other Tenor
Products |
Tenor GateKeeper +
|
Tenor Gatekeeper+ gives enterprises and service
providers a large capacity standalone H.323 compliant gatekeeper
for VoIP networks. The Tenor Gatekeeper+ provides the call routing
and administration for all the H.323 VoIP endpoints in your
network, including gateways, IP phones and PC clients.
The Tenor Gatekeeper+ has the unique ability to
dynamically self configure the VoIP routing database. It will also
support static routing to provide connectivity to endpoints that
are outside of your VoIP network. The advanced call routing
enables the Tenor Gatekeeper+ to provide load balancing among
multiple gateways. The Tenor Gatekeeper+ also provides for
authentication/authorization of all calls in your VoIP network.
|
|
Part Number |
Product Description |
|
501-0197-00 |
Tenor GateKeeper+ Base System
Stand-alone H.323 compliant gatekeeper for use with larger networks
of Tenor switches and other H.323 compliant devices.
Base system must be purchased with a
minimum of either a 20 port, or a 100 port upgrade option.
The GateKeeper+ can be expanded to
support up to 800 H.323 ports and 4,000 DN/IP database entries by
additional software upgrades.
|
|
Tenor Call Relay 60 (Session Border Controller)
|
Tenor Call Relay 60 provides a single VoIP
portal between IP networks allowing for end-to-end VoIP
communications across multiple IP networks. All calls are switched
through multiple IP networks with just one compression and
decompression of the voice. The result is less latency and higher
voice quality as the call traverses through the network.
The Tenor Call Relay 60 allows VoIP endpoints
behind a Network Address Translation (NAT) firewall to communicate
with external VoIP networks. This allows both enterprises and
service providers to expand their VoIP networks to their customers
and partners and across the public Internet.
Tenor Call Relay 60 also provides a single
point for call management, administration and security at the edge
of your VoIP network.
|
|
Part Number |
Product Description |
|
501-0172-00 |
Tenor Call Relay 60 Base System
Tenor Call Relay 60 session border controller provides direct,
secure, IP connections between different VoIP networks, insuring
maximum voice quality and security. The base system supports up to
16 simultaneous VoIP calls between networks. Capacity may be
expanded up to 60 simultaneous VoIP calls (2 E1 spans) by adding
Call Capacity Upgrade Options The Call Relay 60 does not include
Packet Saver. This is available as an optional software upgrade.
Power Requirements : 100 – 240 Volts a.c., 50/60 Hz.
|
|
Tenor Call Relay SP (Session Border Controller)
|
Tenor Call Relay SP Session
Border Controller provides a single VoIP portal between IP
networks allowing for end-to-end VoIP communications across
multiple IP networks. All calls are switched through multiple IP
networks with just one compression and decompression of the voice.
The result is less latency and higher voice quality as the call
traverses through the network.
The Tenor Call Relay SP allows VoIP endpoints
behind a Network Address Translation (NAT) firewall to communicate
with external VoIP networks. This allows both enterprises and
service providers to expand their VoIP networks to their customers
and partners and across the public Internet.
Tenor Call Relay SP also provides a single
point for call management, administration and security at the edge
of your VoIP network.
|
|
Part
Number |
Product
Description |
|
501-0095-00 |
Tenor Call Relay SP Base System (a.c.
power) Tenor Call Relay SP Session Border Controller provides
direct, secure, IP connections between different VoIP networks,
insuring maximum voice quality and security. Supports up to 120
simultaneous VoIP calls between networks. (Equivalent to 5 T1 or 4
E1 spans.) Capacity may be expanded up to 672 simultaneous channels
by adding multiple CR-72 or CR - 120 Upgrade Options.
Power Requirements : 100 – 240 Volts a.c., 50/60 Hz.
|
|
501-0096-00 |
Tenor Call Relay SP Base System (d.c.
power) Tenor Call Relay SP Session Border Controller provides
direct, secure, IP connections between different VoIP networks,
insuring maximum voice quality and security. Supports up to 120
simultaneous VoIP calls between networks. (Equivalent to 5 T1 or 4
E1 spans.) Capacity may be expanded up to 672 simultaneous channels
by adding multiple CR – 120 and CR - 72 Upgrade Options.
Power Requirements : – 48 Volts d.c.
|
|
|
TOP |
|
Quintum’s unique Remote Management Session
Server (RMSS) enables system administrators to manage remote
Tenors even if they are located behind corporate firewalls.
Each RMSS can support a maximum of 100
simultaneous management sessions, from a registered base of up to
5,000 Tenors. Servers can be deployed in redundant configurations
for maximum availability.
The RMSS greatly enhances the responsiveness
and efficiency of customer support groups. It facilitates fast,
and accurate installation, configuration, upgrades and
diagnostics, by giving trained personnel direct access,
eliminating the need for costly truck rolls or service visits.
|
|
Part
Number |
Product
Description |
|
501-0184-00 |
Application Server Base System
Quintum Application Server in 19" rack mounting
chassis. This server is specifically designed to support and run
Quintum VoIP network software applications. Various applications can
be enabled, by adding the appropriate software licenses.
Power Requirements : 100 – 240 Volts a.c., 50/60
Hz.
|
|
Rack Mounting Brackets for AX, BX, DX, Call Relay 60, and
GateKeeper Products
|
Part
Number |
Product
Description |
|
501-0154-00 |
Rack Mounting Brackets for AX, BX,
DX, Call Relay 60, and GK Pair of spare or
replacement rack mounting brackets for use when mounting Tenor AX,
Tenor BX, Tenor DX, Tenor Call Relay 60 or Tenor Gatekeeper
products in a standard nineteen inch equipment rack.
|
Optional Adaptors and Patch Panels for Tenor AX Series Products
8 Port RJ11 Adaptor Unit for 8 Port AX Series Switches
|
This adaptor unit is designed to be used for
simple 8 port applications using standard RJ11 telephone cables.
It offers an economical and convenient method of adapting the 50
pin Telco connectors on the rear of the AX Series switches for
direct connection of RJ11 telephone cables. One adaptor is
required for each 50 pin Telco connector. For AXG800 (FXS only)
applications and AXT800 (FXO only) applications one adaptor is
required. For AXE800 and AXM800 (FXS and FXO) applications two
adaptors are required.
|
|
Part
Number |
Product
Description |
|
501-0169-00 |
50 Pin Telco to 8 port RJ11 Adaptor
Unit for AX Series Tenor This adaptor mounts
directly to the 50 pin Telco FXS or FXO connectors on the rear of
Tenor AX products. It breaks out the first eight FXS or FXO ports of
the twenty four supported by the Telco connector to individual RJ11
ports for use with standard RJ11 telephone cables.
|
|
24 and 48 Port RJ11 Patch Panels for Tenor AX Series
|
These patch panels are designed for use with
the sixteen and twenty four port variants of the AX Series
products. These 1U high rack mounted patch panels break out the
multiple FXS/FXO ports supported by the 50 pin Telco connectors to
individual RJ11 ports for use with standard RJ11 telephone cables.
The patch panels connect to the Tenor AX using standard 50 pin
telco to 50 pin telco cables which must be ordered separately.
These patch panels offer a more economical wiring solution and
convenient front panel access, for customers who wish to use
standard RJ11 cabling.
The 24 port patch panel can be used for FXS
port only (AXG Series) and FXO port only (AXT Series)
applications. The 48 port patch panel can be used for FXS and FXO
port (AXT Series, AXE Series and AXM Series) applications.
|
|
Part
Number |
Product
Description |
|
501-0170-00 |
Rack Mounting 24 Port RJ11 Patch
Panel for AXG/AXT Series This patch panel connects to the 50
pin Telco FXS or FXO connectors on the rear of Tenor AX products
using one 50 Pin Telco to 50 Pin Telco cable. It breaks out the
multiple FXS or FXO ports supported by the Telco connector to
individual RJ11 ports for use with standard RJ11 telephone cables.
Note – A 50 Pin Telco to 50 Pin Telco connecting cable is
required and is NOT included. This item MUST be ordered separately.
|
|
501-0171-00 |
Rack Mounting 48 Port RJ11 Patch
Panel for AXT/AXE/AXM Series This patch panel connects to the
50 pin Telco FXS or FXO connectors on the rear of Tenor AX products
using two 50 Pin Telco to 50 Pin Telco cables. It breaks out the
multiple FXS or FXO ports supported by the Telco connectors to
individual RJ11 ports for use with standard RJ11 telephone cables.
Note – Two 50 Pin Telco to 50 Pin Telco connecting cables are
required and are NOT included. They MUST be ordered separately.
|
|
Cable Options for AX Series Switches
|
The compact size of the Tenor AX Series
products and the need to connect up to 48 separate twisted pair
connections requires the use of 50 pin male Telco connectors. The
two Telco connectors on the rear panel provide termination for up
to 24 FXS and 24 FXO connections. In order to provide for the
different needs of our customers Quintum offers optional cables
with either a 50 pin female Telco connector at each end, or a 50
pin female Telco connector at one end and open ends at the other
for "punch-down" applications.
|
|
Part
Number |
Product
Description |
|
421-0056-00 |
50 Pin Telco Cable Option for AX
Series Tenor (Open Ends) Twenty five pair,
shielded, connection cable for Tenor AX Series products for use in
"Punch-down" applications. This cable is three metres long and is
terminated with a 50 pin female Telco connector at one end and open
ends at the other.
|
|
421-0057-00 |
50 Pin Telco to 50 Pin Telco Cable
Option for AX Series Tenor Twenty five pair,
shielded, interconnection cable for Tenor AX Series products. This
cable is one metre long and is terminated with a 50 pin female Telco
connector at each end. For use with 50 Pin Telco break-out blocks or
Rack Mounting Patch Panels.
|
|
Others Links
Technical specifications are subject to change without
notice.
All brand names and trademarks are the property of their respective owners. |
TOP |
|
|
|
|
|
